MAX4523CEE+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 100Ohm |
| Max Power Dissipation | 762mW |
| Base Part Number | MAX4523 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 80 ns |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 30 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 2V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 2pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 80ns, 30ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -90dB @ 100kHz |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4523CEE+T Overview
The electrical component comes in 16-SSOP (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a number of circuits 1:1. An extended operating temperature of 0°C~70°C TA degrees Celsius. These analog multiplexers are built based on SPST - NO/NC switching circuits. There are 4 circuits in this switch device. MAX4523 can be used to search for analog multiplexer variants. Internally, this switch multiplexer has a resistance of 100Ohm. The functions of 16 pins can be found in the datasheets. In normalcircumstances, users should not exceed 12V volts for the multiplexer. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 2V should be the lowest voltage fed to the electronic component. An operating current of 1μA would be sufficient for this switch device. Putting voltage greater than 1μA on the multiplexer may cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 6V. A dual power supply should have at least 2V voltage attached.
MAX4523CEE+T Features
Switch Circuit: SPST - NO/NC
1μA Supply Current
MAX4523CEE+T Applications
There are a lot of Maxim Integrated MAX4523CEE+T Analog Switches & Multiplexers ICs applications.
- Video switching
- Residential Gateways, Home Gateway/Router
- Remote wireless modules
- Channelized and Unchannelized DS3 applications
- Remote Powered Equipment
- Multiplexers
- Relay Replacement
- PDH Multiplexers
- Industrial and process control systems
- PCMCIA cards
