MAX4523ESE+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX4523 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 6V |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 80 ns |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 2pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 80ns, 30ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 30ns |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4523ESE+T Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. In total, there have been 16 terminations. A high-quality output is provided by the electrical component's 1 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. The electrical component body receives 16 pins. On the other hand, analog switches can be constructed using SPST - NO/NC switching circuits. There are 4 circuits in this multiplexer. If you are looking for variants of the digital switch, trying search with MAX4523. Analog switches have 100Ohm internal resistance. For functions related to 16 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. Users should never supply a voltage higher than 12V to a switch device. An effective Dual, Single supply digital multiplexer. A low voltage of 2V should be applied to the electronic component. For this digital switch to work, 1μA current would suffice. Put voltage above 1μA on the multiplexer to cause damage. For this switch, a dual supply voltage is feasible, but it must not exceed 6VWith dual power supplies, you should attach at least 2V. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. Operating voltages range from 6V.
MAX4523ESE+T Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
MAX4523ESE+T Applications
There are a lot of Maxim Integrated MAX4523ESE+T Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- Switching Systems
- Audio and video signal routing
- PCMCIA cards
- Transmit
- Private Branch Exchange (PBX)
- High reliability control systems
- Public switching systems
- Routers
- Precision data acquisition
