MAX4525CUB

150ns, 120ns DPDT 150Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4525 10 Pins 1nA 3V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4525CUB
Package: 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
Datasheet: PDF
Stock: 243
Description: 150ns, 120ns DPDT 150Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4525 10 Pins 1nA 3V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)(Kg)

Inquiry Now

Details

Tags

Parameters
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
Number of Pins	10
Operating Temperature	0°C~70°C TA
Packaging	Tube
Published	2007
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	10
ECCN Code	EAR99
Resistance	150Ohm
Max Power Dissipation	330mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	240
Number of Functions	1
Supply Voltage	3V
Terminal Pitch	0.5mm
Time@Peak Reflow Temperature-Max (s)	20
Base Part Number	MAX4525
Output	SEPARATE OUTPUT
Pin Count	10
Operating Supply Voltage	5V
Number of Channels	2
Number of Circuits	1
Max Supply Voltage	12V
Min Supply Voltage	2V
Operating Supply Current	1μA
Nominal Supply Current	10μA
Max Supply Current	1μA
Number of Bits	4
Turn On Delay Time	200 ns
Logic Function	Multiplexer
Supply Type	Single
Turn-Off Delay Time	300 ns
On-State Resistance (Max)	150Ohm
Multiplexer/Demultiplexer Circuit	2:2
Off-state Isolation-Nom	75 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	4pF 6pF
On-state Resistance Match-Nom	2Ohm
Switch Circuit	DPDT
Switch Time (Ton, Toff) (Max)	150ns, 120ns
Charge Injection	0.8pC
Channel-to-Channel Matching (ΔRon)	2 Ω
Crosstalk	-74dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+)	2V~12V
Length	3mm
Width	3mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	Non-RoHS Compliant
Lead Free	Contains Lead

MAX4525CUB Overview

Packed in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width), the electronic component is convenient for shipping overseas. High reliability is ensured by the advanced packaging method Tube. Multiplexers like this are mounted in the Surface Mount position. 2:2 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around 0°C~70°C TA. Totally, there are 10 terminations. The electronic part delivers high-quality output through its 2 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. A key feature of the 10 series is the inclusion of this electronic part as part of its design. Unlike digital switches, these are based on DPDT switching circuits. 1 circuits are used in this analogue multiplexer. MAX4525 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 150Ohm. For details about the functions of 10 pins, please refer to the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. A cost-effective Single supply type analogue multiplexer. There should be 2V voltage fed to the electrical part below 2V. It would be sufficient to run this analogue multiplexer with 1μA current. A voltage of 2V~12V is required to drain this analog switch from a single voltage supply. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. The electronic component can function from 5V. 4-bit operation is possible.