MAX4525EUB

150ns, 120ns DPDT 150Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4525 10 Pins 1nA 3V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4525EUB
Package: 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
Datasheet: PDF
Stock: 687
Description: 150ns, 120ns DPDT 150Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4525 10 Pins 1nA 3V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)(Kg)

Inquiry Now

Details

Tags

Parameters
REACH SVHC	Unknown
RoHS Status	Non-RoHS Compliant
Lead Free	Contains Lead
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
Number of Pins	10
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2007
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	10
ECCN Code	EAR99
Resistance	150Ohm
Max Power Dissipation	330mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	240
Number of Functions	1
Supply Voltage	3V
Terminal Pitch	0.5mm
Time@Peak Reflow Temperature-Max (s)	20
Base Part Number	MAX4525
Output	SEPARATE OUTPUT
Pin Count	10
Operating Supply Voltage	5V
Number of Channels	2
Number of Circuits	1
Max Supply Voltage	12V
Min Supply Voltage	2V
Operating Supply Current	1μA
Nominal Supply Current	10μA
Max Supply Current	1μA
Number of Bits	4
Turn On Delay Time	200 ns
Logic Function	Multiplexer
Supply Type	Single
Turn-Off Delay Time	300 ns
On-State Resistance (Max)	150Ohm
Multiplexer/Demultiplexer Circuit	2:2
Off-state Isolation-Nom	75 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	4pF 6pF
On-state Resistance Match-Nom	2Ohm
Switch Circuit	DPDT
Switch Time (Ton, Toff) (Max)	150ns, 120ns
Charge Injection	0.8pC
Channel-to-Channel Matching (ΔRon)	2 Ω
Crosstalk	-74dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+)	2V~12V
Height	950μm
Length	3.05mm
Width	3.05mm
Radiation Hardening	No

MAX4525EUB Overview

Packed in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width), the electronic component is convenient for shipping overseas. To ensure high reliability, a new packaging method Tube is used. Multiplexers like this are mounted in the Surface Mount position. 2:2 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. Totally, there are 10 terminations. The electronic part provides high-quality output because it has 2 channels. An 3V voltage supply should allow the electrical part to be turned on and run. This electronic part can be found in the 10 series. Multiplexers built on a DPDT switching circuit are built. There are 1 circuits in this switch device. Look for analog switch ic variants by searching with MAX4525. Analog switches have 150Ohm internal resistance. The functions of 10 pins can be found in the datasheets. Users shouldn't supply more than 12V voltage to the switch device. A analog switch ic that has a cost-effective Single supply type. The lowest voltage fed to the electronic component should be 2V. In order to operate this switch device, it would need a current of 1μA. A voltage of 2V~12V is required to drain this analog switch from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. The electronic component can function from 5V. It can conduct 4-bit signals.