MAX4525LETB+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-WFDFN Exposed Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 150Ohm |
| Terminal Finish | MATTE TIN |
| Max Power Dissipation | 330mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX4525 |
| Pin Count | 10 |
| Number of Channels | 2 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12.6V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 10μA |
| Turn On Delay Time | 200 ns |
| Logic Function | Multiplexer |
| Supply Type | Single |
| Turn-Off Delay Time | 300 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 80Ohm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 92 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 6pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 150ns, 120ns |
| Charge Injection | 0.8pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -96dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~12V |
| Signal Current-Max | 0.02A |
| Height Seated (Max) | 0.8mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4525LETB+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 10-WFDFN Exposed Pad. High reliability is achieved by using advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. In the multiplexer and demultiplexer, 2:2 represents the number of circuits. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 10. The electronic part delivers high-quality output through its 2 channels. When the electronic component is given a voltage of 12V, it should be turned on and run. 10 pins are injected to the electronic part body. Based on DPDT switching circuits, these analog multiplexers work. 1 circuits are used in this analogue multiplexer. Use MAX4525 to search for variants of the digital switches. This digital multiplexer has 150Ohm internal resistance. You can find the functions of the 10 pins in the datasheets. Multiplexers should not be powered above 12.6V in normal situations. A cost-effective Single supply type analogue multiplexer. The lowest voltage fed to the electronic component should be 2V. An operating current of 1μA would be sufficient for this switch device. Analogue multiplexers require a 2V~12V voltage to drain from a single voltage supply.
MAX4525LETB+T Features
2 Channels
Switch Circuit: DPDT
1μA Supply Current
-3db Bandwidth: 200MHz
MAX4525LETB+T Applications
There are a lot of Maxim Integrated MAX4525LETB+T Analog Switches & Multiplexers ICs applications.
- Communication systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Avionics
- Sample-and-hold systems
- Private Branch Exchange (PBX)
- Remote Powered Equipment
- DSUs
- Digital access cross connects
- High speed data transmission line cards
- Data Acquisition Systems
