MAX4526CUA+T

SPDT 175Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4526 8 Pins 500pA 15V 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4526CUA+T
Package: 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
Datasheet: PDF
Stock: 701
Description: SPDT 175Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4526 8 Pins 500pA 15V 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)(Kg)

Details

Tags

Parameters
Mounting Type	Surface Mount
Package / Case	8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
Surface Mount	YES
Number of Pins	8
Operating Temperature	0°C~70°C TA
Packaging	Tape & Reel (TR)
Published	1997
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
Resistance	175Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	471mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	15V
Terminal Pitch	0.65mm
Base Part Number	MAX4526
Pin Count	8
Operating Supply Voltage	20V
Power Supplies	+-15V
Number of Channels	1
Number of Circuits	2
Max Supply Voltage	36V
Min Supply Voltage	4.5V
Analog IC - Other Type	SPST
Nominal Supply Current	50nA
Max Supply Current	1mA
Voltage - Supply, Single/Dual (±)	4.5V~36V ±4.5V~18V
Neg Supply Voltage-Nom (Vsup)	-15V
Max Dual Supply Voltage	20V
On-State Resistance (Max)	175Ohm
Min Dual Supply Voltage	4.5V
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	65 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	13pF
On-state Resistance Match-Nom	0.5Ohm
Switch Circuit	SPDT
Charge Injection	1pC
Channel-to-Channel Matching (ΔRon)	500m Ω
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	0.1ns
Switch-off Time-Max	0.1ns
Height Seated (Max)	1.1mm
Length	3mm
Width	3mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

MAX4526CUA+T Overview

The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:1. An extended operating temperature of 0°C~70°C TA degrees Celsius. In total, 8 terminations have occurred. A high-quality output is provided by the electrical component's 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. It is injected into the electrical part body with 8 pins. Circuits based on SPDT switching are used to construct these analog switch ics. The circuits in this analogue multiplexer number 2. Look for analog switch ic variants by searching with MAX4526. A 175Ohm internal resistance characterizes this multiplexer. To find out what the functions of 8 pins are, please refer to their datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users shouldn't supply more than 36V voltage to the switch device. It is recommended that the electrical component receives a voltage of 4.5V. When the digital multiplexer is charged above 1mA, damage can occur. Despite this switch device's dual supply capability, its voltage should not exceed 20V. In the case of dual power supplies, you should connect at least 4.5V. An analog IC with the number SPST is integrated into this board. 20V operating voltages can be used with this electrical part.