MAX4526EPA
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4526 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Analog IC - Other Type | SPST |
| Max Supply Current | 1mA |
| Turn On Delay Time | 100 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 13pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 0.1ns |
| Switch-off Time-Max | 0.1ns |
| Length | 9.375mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4526EPA Overview
Packed in 8-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. The advanced packaging method Tube provides high reliability. It is mounted in the position Through Hole. Multiplexers and demultiplexers have a ratio of 2:1. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 8. A 1 channel electronic part produces high-quality output. A 15V voltage supply should turn on and run the electronic component. An electrical component of this type can be found in the 8 series. The analog switch ics are built using SPDT switching circuits. There are 2 circuits in this switch device. If you are looking for variants of the digital switch, trying search with MAX4526. This digital multiplexer has 175Ohm internal resistance. To find out what the functions of 8 pins are, please refer to their datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. Multiplexers should not be powered above 36V in normal situations. The digital multiplexer has a low cost Dual, Single supply. In order for the electronic part to function properly, the lowest voltage should be 4.5V. If put voltage greater than 1mA on the device, damage may be caused to the analogue multiplexer. For this multiplexer, dual supply voltage is feasible, but it should not exceed 18V. If you are using a dual power supply, you should attach at least 4.5V. There is an integrated analog IC SPST in the module.
MAX4526EPA Features
1 Channels
Switch Circuit: SPDT
MAX4526EPA Applications
There are a lot of Maxim Integrated MAX4526EPA Analog Switches & Multiplexers ICs applications.
- CSU
- Medical Instrumentation
- Microprocessor Controlled Analog Systems
- Precision instrumentation
- Automotive applications
- PBXs
- Public switching systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- DSLAMs
- Relay replacements
