MAX4526ESA
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4526 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Polarity | Non-Inverting |
| Power Supplies | +-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Analog IC - Other Type | SPST |
| Operating Supply Current | 700μA |
| Nominal Supply Current | 50nA |
| Max Supply Current | 1mA |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 13pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 0.1ns |
| Switch-off Time-Max | 0.1ns |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Contact Plating | Tin |
| Mount | Surface Mount |
MAX4526ESA Overview
Due to its 8-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. High reliability is provided by advanced packaging method Tube. It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. Extended operating temperature around -40°C~85°C TA. 8 terminations have been made so far. A electrical component with 1 channels is capable of high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. The electrical component body receives 8 pins. A SPDT switching circuit is used to build these analog multiplexers. It consists of 2 circuits. Look for analog switch ic variants by searching with MAX4526. Analog switches have 175Ohm internal resistance. To find out what the functions of 8 pins are, please refer to their datasheets. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 36V. An effective Dual, Single supply digital multiplexer. It is recommended to use 4.5V as the lowest voltage for the electrical part. This digital switch can be operated with a current of 700μA. If put voltage greater than 1mA on the device, damage may be caused to the analogue multiplexer. Despite this switch device's dual supply capability, its voltage should not exceed 20V. When using dual power supplies, you should attach at least 4.5V. Integrated with an analog IC SPST. A voltage of 20V can be used to operate the electronic component.
MAX4526ESA Features
1 Channels
Switch Circuit: SPDT
700μA Supply Current
MAX4526ESA Applications
There are a lot of Maxim Integrated MAX4526ESA Analog Switches & Multiplexers ICs applications.
- Multi-Line E1 Interface Cards
- Medical systems
- Avionics test equipment
- DSUs
- Signal routing between systems
- ATM
- Digital access cross connects
- Remote wireless modules
- T1/E1 Terminals
- Existing multiplexer applications (both fault-protected and nonfault-protected)
