MAX4526ESA+T
| Parameters | |
|---|---|
| Published | 1997 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 175Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | MAX4526 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Operating Supply Voltage | 20V |
| Power Supplies | +-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Analog IC - Other Type | SPST |
| Operating Supply Current | 700μA |
| Nominal Supply Current | 50nA |
| Max Supply Current | 1mA |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 13pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 0.1ns |
| Switch-off Time-Max | 0.1ns |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
MAX4526ESA+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-SOIC (0.154, 3.90mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. Multiplexer and demultiplexer circuits have a number 2:1. Increasing operating temperature to around -40°C~85°C TA. In total, there are 8 terminations. As a result of its 1 channels, this electronic component provides high-quality output. A 15V voltage supply should turn on and run the electronic component. A total of 8 pins are injected into the electrical part body. Multiplexers built on a SPDT switching circuit are built. Circuits number 2 make up this analogue multiplexer. Try searching with MAX4526 if you're looking for variants. As far as internal resistance is concerned, it has 175Ohm. There is a standard Multiplexer or Switches analogue multiplexer here. normally, users should not supply switches with voltages higher than 36V. Digital switch that provides Dual, Single power at a cost-effective price. A low voltage of 4.5V should be applied to the electronic component. This digital switch can be operated with a current of 700μA. Putting voltage greater than 1mA on the multiplexer may cause damage. Despite this switch's dual supply capability, its voltage should not exceed 20V. With dual power supplies, you should attach at least 4.5V. It is integrated with SPST analog ICs. 20V operating voltages can be used with this electrical part.
MAX4526ESA+T Features
1 Channels
Switch Circuit: SPDT
700μA Supply Current
MAX4526ESA+T Applications
There are a lot of Maxim Integrated MAX4526ESA+T Analog Switches & Multiplexers ICs applications.
- Video signal routing
- Precision test equipment
- Communication systems
- Audio/video switches
- Frame Relay Equipment
- Precision data acquisition
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Audio and video signal routing
- Communication systems
- Mechanical reed relay replacement
