MAX4527CPA
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4527 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Power Supplies | +-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Analog IC - Other Type | SPST |
| Nominal Supply Current | 50nA |
| Max Supply Current | 1μA |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 13pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Length | 9.375mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
MAX4527CPA Overview
Shipping overseas is convenient due to the electrical component's packing in 8-DIP (0.300, 7.62mm). In order to provide high reliability, an advanced packaging method Tube is used. Through Hole is where this multiplexer is located. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Operational temperature extended around 0°C~70°C TA. The total number of terminations is 8. A high-quality output is provided by the electrical component's 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. A total of 8 pins are injected into the body of the electronic part. Unlike digital switches, these are based on SPDT switching circuits. This multiplexer is composed of 2 circuits. If you are looking for variants of the digital switch, trying search with MAX4527. Internally, this switch multiplexer has a resistance of 175Ohm. Datasheets for functions of 8 pins are available. Theswitch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 36V in normal situations. Dual, Single supply type digital switch with a low cost. 4.5V is the lowest voltage that should be fed to the electronic electronic part. A voltage higher than 1μA may cause damage to the switch multiplexer. Despite this switch's dual supply capability, its voltage should not exceed 20V. With dual power supplies, you should attach at least 4.5V. This product is integrated with an analog integrated circuit (IC) of type SPST. 20V operating voltages are supported by the electronic component.
MAX4527CPA Features
1 Channels
Switch Circuit: SPDT
MAX4527CPA Applications
There are a lot of Maxim Integrated MAX4527CPA Analog Switches & Multiplexers ICs applications.
- Central office
- Communication systems
- ATM
- Power routing
- DSLAMs
- Industrial and process control systems
- Fiber In The Loop (FITL)
- Multiplexers
- Public switching systems
- Audio signal routing
