MAX4527CSA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4527 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Power Supplies | +-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Analog IC - Other Type | SPST |
| Nominal Supply Current | 50nA |
| Max Supply Current | 1μA |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 13pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4527CSA+ Overview
Packed in 8-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. Advanced packaging method Tube is used to provide high reliability. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. Increasing operating temperature to around 0°C~70°C TA. Total terminations are 8. The electronic part provides high-quality output because it has 1 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. An electrical component of this type can be found in the 8 series. These analog multiplexers are built based on SPDT switching circuits. There are 2 circuits in this switch device. If you are looking for variants of the digital switch, trying search with MAX4527. Internally, this switch multiplexer has a resistance of 175Ohm. The datasheets for the 8 pins explain the functions. It is a typical Multiplexer or Switches analog multiplexer. normally, users should not supply switches with voltages higher than 36V. The digital multiplexer has a low cost Dual, Single supply. The lowest voltage the electronic part should receive is 4.5V. A digital multiplexer may suffer damage if voltage is applied above 1μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. Integrated with an analog IC SPST. It can operate from 20V operating voltages.
MAX4527CSA+ Features
1 Channels
Switch Circuit: SPDT
MAX4527CSA+ Applications
There are a lot of Maxim Integrated MAX4527CSA+ Analog Switches & Multiplexers ICs applications.
- Data switching
- Communication systems
- Precision test equipment
- DVD-R
- Mechanical reed relay replacement
- Residential Gateways, Home Gateway/Router
- Remote wireless modules
- High speed data transmission line cards
- RGB switches
- Channelized and Unchannelized DS3 applications
