MAX4527CUA
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4527 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Power Supplies | +-15V |
| Number of Channels | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Analog IC - Other Type | SPST |
| Nominal Supply Current | 50nA |
| Max Supply Current | 1μA |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 13pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4527CUA Overview
The electronic component is convenient to ship overseas because it is packed in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). To ensure high reliability, a new packaging method Tube is used. In Surface Mount, this analog switch is mounted. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature extended to 0°C~70°C TA. The total number of terminations is 8. A 2 channel electronic part produces high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. 8 pins are injected to the electronic part body. These analog multiplexers are built based on SPDT switching circuits. If you are looking for variants of the digital switch, trying search with MAX4527. This digital multiplexer has 175Ohm internal resistance. The datasheets for the 8 pins explain the functions. The analog multiplexer shown here is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 36V. The digital multiplexer has a low cost Dual, Single supply. 4.5V should be the lowest voltage fed to the electronic component. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. Despite this switch's dual supply capability, its voltage should not exceed 20V. It is recommended that you attach at least 4.5V to your dual power supply. Integrated with an analog IC SPST. It can operate from 20V operating voltages.
MAX4527CUA Features
2 Channels
Switch Circuit: SPDT
MAX4527CUA Applications
There are a lot of Maxim Integrated MAX4527CUA Analog Switches & Multiplexers ICs applications.
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Signal routing between systems
- E1 Multiplexer
- Imaging
- PBX interfaces
- Cell phones
- Private Branch Exchange (PBX)
- Video signal routing
- Relay replacements
- Sample-and-hold systems
