MAX4527ESA
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4527 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Polarity | Non-Inverting |
| Power Supplies | +-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Analog IC - Other Type | SPST |
| Nominal Supply Current | 50nA |
| Max Supply Current | 1μA |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 13pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4527ESA Overview
Packed in 8-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. Advanced packaging method Tube is used to provide high reliability. Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a number of circuits 2:1. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 8. By its 1 channels, the electronic component provides high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. There is an electrical component included in the 8 series. Unlike digital switches, these are based on SPDT switching circuits. It consists of 2 circuits. If you are looking for variants of the digital switch, trying search with MAX4527. This digital multiplexer has 175Ohm internal resistance. Please refer to the datasheets for 8 pins functions. Theswitch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 36V volts for the multiplexer. A analog switch ic that has a cost-effective Dual, Single supply type. In order for the electronic part to function properly, the lowest voltage should be 4.5V. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. Despite this switch device's dual supply capability, its voltage should not exceed 20V. You should attach at least 4.5V voltage if you are using dual power supply. There is an analog IC SPST integrated with this board. It can operate from 20V operating voltages.
MAX4527ESA Features
1 Channels
Switch Circuit: SPDT
MAX4527ESA Applications
There are a lot of Maxim Integrated MAX4527ESA Analog Switches & Multiplexers ICs applications.
- High reliability control systems
- Fault Tolerant Systems
- SONET/SDH ADM
- 65 V DACs
- DSUs
- Automatic test equipment
- Cable PC
- New designs requiring multiplexer functions
- FTTH
- Avionics test equipment
