MAX4527EUA
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4527 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Power Supplies | +-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Analog IC - Other Type | SPST |
| Nominal Supply Current | 50nA |
| Max Supply Current | 1μA |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 13pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
MAX4527EUA Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). This high-reliability packaging method uses advanced packaging methods Tube. The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. The operating temperature is extended to around -40°C~85°C TA. A total of 8 terminations have been recorded. The electronic part delivers high-quality output through its 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. There are 8 pins injected into the electronic part body. SPDT switching circuits are used in these analog switch ics. Circuits number 2 make up this analogue multiplexer. If you are looking for variants of the digital switch, trying search with MAX4527. An switch multiplexer with 175Ohm internal resistance has a value of 175Ohm. Datasheets for 8 pin functions are available upon request. There is Multiplexer or Switches analog multiplexer like this in the world. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. The digital multiplexer has a low cost Dual, Single supply. In order for the electronic part to function properly, the lowest voltage should be 4.5V. Putting voltage greater than 1μA on the multiplexer may cause damage. There is no problem with using dual supply voltage, but it should not exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. There is an integrated analog IC SPST in the module. Operating voltages of 20V are compatible with the electrical part.
MAX4527EUA Features
1 Channels
Switch Circuit: SPDT
MAX4527EUA Applications
There are a lot of Maxim Integrated MAX4527EUA Analog Switches & Multiplexers ICs applications.
- PDAs
- Digital cross connects (DSX-1)
- Communications systems
- Sample-and-hold systems
- HDTV
- Mechanical reed relay replacement
- SDH/SONET multiplexers
- Communication systems
- SONET
- Precision data acquisition
