MAX4528CSA
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1998 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 110Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 330mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4528 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Operating Supply Voltage | 6V |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Analog IC - Other Type | DPDT |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 10μA |
| Max Supply Current | 1μA |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±2.7V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 110Ohm |
| Min Dual Supply Voltage | 2.7V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 13pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SPDT |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 150ns |
| Switch-off Time-Max | 100ns |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4528CSA Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-SOIC (0.154, 3.90mm Width). Advanced packaging method Tube is used to provide high reliability. This analog switch is mounted in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Temperatures around 0°C~70°C TA are extended for operation. 8 terminations have been made so far. A 2 channel electronic part produces high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. It is injected into the electrical part body with 8 pins. These analog multiplexers are built based on SPDT switching circuits. Try searching with MAX4528 if you're looking for variants. This digital multiplexer has 110Ohm internal resistance. The datasheets for the 8 pins explain the functions. Multiplexer or Switches is a typical switch device. Users shouldn't supply more than 12V voltage to the switch device. Dual, Single supply type digital switch with a low cost. A low voltage of 2.7V should be applied to the electronic component. The analogue multiplexer could operate on 1μA current. A digital multiplexer may suffer damage if voltage is applied above 1μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 6V. With dual power supplies, you should attach at least 2.7V. It is integrated with a DPDT analog IC. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. A voltage of 6V can be used to operate the electronic component.
MAX4528CSA Features
2 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX4528CSA Applications
There are a lot of Maxim Integrated MAX4528CSA Analog Switches & Multiplexers ICs applications.
- Isolation
- Channelized and Unchannelized DS3 applications
- Medical systems
- Routers
- High speed data transmission line cards
- Data switching
- USB 1.1 signal switching circuits
- Cross Connects
- Signal routing between systems
- Medical
