MAX4528CSA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1998 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 110Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 330mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4528 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Operating Supply Voltage | 6V |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Analog IC - Other Type | DPDT |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 10μA |
| Max Supply Current | 1μA |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±2.7V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 110Ohm |
| Min Dual Supply Voltage | 2.7V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 13pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SPDT |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 150ns |
| Switch-off Time-Max | 100ns |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4528CSA+T Overview
Shipping overseas is convenient with the electronic component packed in 8-SOIC (0.154, 3.90mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. 2:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around 0°C~70°C TA. In total, 8 terminations have occurred. A electrical component with 2 channels is capable of high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. There is an electrical component included in the 8 series. These analog multiplexers are built based on SPDT switching circuits. It consists of 2 circuits. Using the MAX4528 search parameter, you can discover variants of the switch. As far as internal resistance is concerned, it has 110Ohm. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 2.7V is the lowest voltage the electrical component should receive. The switch device would be able to operate with 1μA current. It may damage the digital multiplexer if the voltage is higher than 1μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 6V. You should attach at least 2.7V voltage if you are using dual power supply. It is integrated with a DPDT analog IC. There are SEPARATE OUTPUT outputs on this analog switch ic. Operating voltages of 6V are compatible with the electrical part.
MAX4528CSA+T Features
2 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX4528CSA+T Applications
There are a lot of Maxim Integrated MAX4528CSA+T Analog Switches & Multiplexers ICs applications.
- Voice over IP/DSL – Integrated Access Devices, Smart
- Digital cross connects (DSX-1)
- Industrial control systems
- Digital access cross connects
- Mechanical reed relay replacement
- DSLAMs
- Automatic test equipment
- Medical
- Audio and video switching
- Power routing
