banner_page

MAX4528ESA+T

SPDT 110Ohm Analog Switches MAX4528 8 Pins 500pA 5V 8-SOIC (0.154, 3.90mm Width)


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX4528ESA+T
  • Package: 8-SOIC (0.154, 3.90mm Width)
  • Datasheet: PDF
  • Stock: 936
  • Description: SPDT 110Ohm Analog Switches MAX4528 8 Pins 500pA 5V 8-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Supply Type Dual, Single
Neg Supply Voltage-Nom (Vsup) -5V
Max Dual Supply Voltage 6V
On-State Resistance (Max) 110Ohm
Min Dual Supply Voltage 2.7V
Multiplexer/Demultiplexer Circuit 2:1
Current - Leakage (IS(off)) (Max) 500pA
Channel Capacitance (CS(off), CD(off)) 13pF
On-state Resistance Match-Nom 4Ohm
Switch Circuit SPDT
Charge Injection 1pC
Channel-to-Channel Matching (ΔRon) 3 Ω
Switch-on Time-Max 150ns
Switch-off Time-Max 100ns
Height Seated (Max) 1.75mm
Length 4.9mm
Width 3.9mm
Radiation Hardening No
RoHS Status ROHS3 Compliant
Factory Lead Time 1 Week
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 8-SOIC (0.154, 3.90mm Width)
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 1998
JESD-609 Code e3
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
ECCN Code EAR99
Resistance 110Ohm
Terminal Finish Matte Tin (Sn)
Max Power Dissipation 330mW
Technology CMOS
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 5V
Base Part Number MAX4528
Pin Count 8
JESD-30 Code R-PDSO-G8
Operating Supply Voltage 6V
Number of Channels 2
Number of Circuits 2
Max Supply Voltage 12V
Min Supply Voltage 2.7V
Analog IC - Other Type DPDT
Operating Supply Current 1μA
Nominal Supply Current 10μA
Max Supply Current 1μA
Voltage - Supply, Single/Dual (±) 2.7V~12V ±2.7V~6V

MAX4528ESA+T Overview


The electrical component comes in 8-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Surface Mount is where this multiplexer is located. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Operating temperature extended to -40°C~85°C TA. Totally, there are 8 terminations. A electrical component with 2 channels is capable of high-quality output. When a voltage supply of 5V is used, the electronic component should be turned on and run. This electronic part can be found in the 8 series. These analog multiplexers are built based on SPDT switching circuits. Circuits number 2 make up this analogue multiplexer. Try searching for the analog switch ic with MAX4528 if you are looking for variants. In this multiplexer, the internal resistance is 110Ohm. It is generally not recommended to supply a voltage higher than 12V to the switch device in normal circumstances. The analog switch ic is of the Dual, Single supply type and is cost-effective. There should be 2.7V voltage fed to the electrical part below 2.7V. An operating current of 1μA would be sufficient for this switch device. Putting voltage greater than 1μA on the multiplexer may cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 6V. If you are using dual power supplies, you should attach at least 2.7V. There is an analog IC DPDT integrated with this board. It can operate from 6V operating voltages.

MAX4528ESA+T Features


2 Channels
Switch Circuit: SPDT
1μA Supply Current

MAX4528ESA+T Applications


There are a lot of Maxim Integrated MAX4528ESA+T Analog Switches & Multiplexers ICs applications.

  • Relay replacements
  • Avionics and Military Systems
  • Industrial control systems
  • Cable Modem
  • E1 Network Equipment
  • Automotive applications
  • PCMCIA cards
  • DSUs
  • Routers
  • Voice over IP/DSL – Integrated Access Devices, Smart

Write a review

Note: HTML is not translated!
    Bad           Good