MAX4530EAP
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2001 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 75Ohm |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX4530 |
| Pin Count | 20 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Throw Configuration | SP8T |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 350 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 75Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 15pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 1.5pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -92dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Length | 7.2mm |
| Width | 5.29mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4530EAP Overview
Shipping overseas is convenient with the electronic component packed in 20-SSOP (0.209, 5.30mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. Surface Mount is where this multiplexer is located. In the multiplexer and demultiplexer, 8:1 represents the number of circuits. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 20. A 8 channel electronic part produces high-quality output. A 5V voltage supply should turn on and run the electronic component. It is injected into the electrical part body with 20 pins. The multiplexer consists of 1 circuits. Try searching for the analog switch ic with MAX4530 if you are looking for variants. There is 75Ohm internal resistance in this digital multiplexer. For functions related to 20 pins, please refer to the datasheets. normally, users should not supply switches with voltages higher than 12V. A cost-effective Dual, Single supply type analogue multiplexer. 2V should be the lowest voltage fed to the electronic component. This multiplexer would work with 1μA current. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 6V. The voltage should be at least 2V if you are using dual power supplies. 9V operating voltages can be used with this electrical part.
MAX4530EAP Features
8 Channels
1μA Supply Current
MAX4530EAP Applications
There are a lot of Maxim Integrated MAX4530EAP Analog Switches & Multiplexers ICs applications.
- DSLAMs
- Precision data acquisition
- PBX interfaces
- Communication systems
- Data switching
- PBXs
- Cellular phones
- Channel Banks
- Precision instrumentation
- Digital Cross-Connects
