MAX4531EWP+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2001 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 75Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4531 |
| Pin Count | 20 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Throw Configuration | 4PST |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 350 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 0.01mA |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 75Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 15pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 1.5pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -92dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 100ns |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
MAX4531EWP+ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 20-SOIC (0.295, 7.50mm Width). In order to provide high reliability, an advanced packaging method Tube is used. A switch device like this is mounted in Surface Mount. 4:1 is the ratio between multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. Totally, there are 20 terminations. This electronic part offers high-quality output due to its 4 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. A total of 20 pins are injected into the body of the electronic part. These analog multiplexers are built based on SP4T switching circuits. The circuits in this analogue multiplexer number 2. Try searching for the analog switch ic with MAX4531 if you are looking for variants. Internally, this switch multiplexer has a resistance of 75Ohm. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. There should be 2V voltage fed to the electrical part below 2V. It would be sufficient to run this analogue multiplexer with 1μA current. For this multiplexer, dual supply voltage is feasible, but it should not exceed 6V. If you are using a dual power supply, you should attach at least 2V. The electrical part can be operated at 9V voltage levels.
MAX4531EWP+ Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
MAX4531EWP+ Applications
There are a lot of Maxim Integrated MAX4531EWP+ Analog Switches & Multiplexers ICs applications.
- Audio signal routing
- Battery-powered systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Multi-Line E1 Interface Cards
- Medical
- Precision test equipment
- Cross Connects
- E1 Network Equipment
- DSUs
- Microprocessor Controlled Analog Systems
