Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
20-SOIC (0.295, 7.50mm Width) |
Number of Pins |
20 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2001 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
20 |
ECCN Code |
EAR99 |
Resistance |
75Ohm |
Terminal Finish |
Matte Tin (Sn) |
Max Power Dissipation |
800mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
3 |
Supply Voltage |
5V |
Terminal Pitch |
1.27mm |
Base Part Number |
MAX4532 |
Pin Count |
20 |
Operating Supply Voltage |
6V |
Number of Channels |
1 |
Number of Circuits |
3 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2V |
Operating Supply Current |
1nA |
Propagation Delay |
150 ns |
Turn On Delay Time |
150 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
2V~12V ±2V~6V |
Supply Type |
Dual, Single |
Supply Current-Max (Isup) |
0.01mA |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
120 ns |
Max Dual Supply Voltage |
6V |
On-State Resistance (Max) |
75Ohm |
Min Dual Supply Voltage |
2V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
65 dB |
Channel Capacitance (CS(off), CD(off)) |
3pF 15pF |
On-state Resistance Match-Nom |
1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
150ns, 100ns |
Charge Injection |
1.5pC |
Channel-to-Channel Matching (ΔRon) |
1 Ω |
Crosstalk |
-92dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Signal Current-Max |
0.02A |
Height Seated (Max) |
2.65mm |
Length |
12.8mm |
Width |
7.5mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX4532CWP+ Overview
This electronic part is conveniently packaged in 20-SOIC (0.295, 7.50mm Width), making it easy to ship abroad. In order to provide high reliability, an advanced packaging method Tube is used. There is an analog multiplexer mounted in position Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around 0°C~70°C TA. There are 20 terminations totally. Due to its 1 channels, the electrical component produces high-quality output. When a voltage supply of 5V is used, the electronic component should be turned on and run. This electronic part can be found in the 20 series. SPDT switching circuits are used in these analog switch ics. There are 3 circuits in this multiplexer. Try searching with MAX4532 if you're looking for variants. This digital multiplexer has 75Ohm internal resistance. For functions related to 20 pins, please refer to the datasheets. A voltage higher than 12V should not normally be supplied to the switches. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 2V. The analogue multiplexer could operate on 1nA current. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 6V. It is recommended that you attach at least 2V to your dual power supply. Operating voltages of 6V are compatible with the electrical part.
MAX4532CWP+ Features
1 Channels
Switch Circuit: SPDT
1nA Supply Current
MAX4532CWP+ Applications
There are a lot of Maxim Integrated MAX4532CWP+ Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- Communication systems
- Remote wireless modules
- Microprocessor controlled systems
- Audio signal routing
- PDH Multiplexers
- Switching Systems
- DSLAMs
- Low-Voltage
- Video switching