MAX4532EAP
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2001 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 75Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX4532 |
| Pin Count | 20 |
| Operating Supply Voltage | 9V |
| Number of Channels | 1 |
| Number of Circuits | 3 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 350 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 0.01mA |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 75Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 15pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 1.5pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -92dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Height Seated (Max) | 1.99mm |
| Length | 7.2mm |
| Width | 5.29mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4532EAP Overview
Shipping overseas is convenient due to the electrical component's packing in 20-SSOP (0.209, 5.30mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. There is an analog multiplexer mounted in position Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. In total, there have been 20 terminations. Due to its 1 channels, the electrical component produces high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. An electrical component like this is included in the 20 series. The analog switch ics are built using SPDT switching circuits. A 3 circuit is present in this switch device. Try searching with MAX4532 if you're looking for variants. This digital multiplexer has 75Ohm internal resistance. For details about the functions of 20 pins, please refer to the datasheets. A voltage higher than 12V should not normally be supplied to the switches. Analog switch ics with Dual, Single supply type are cost-effective. The lowest voltage the electronic part should receive is 2V. For this digital switch to work, 1μA current would suffice. Despite this switch's dual supply capability, its voltage should not exceed 6V. With dual power supplies, you should attach at least 2V. There is a voltage range of 9V operating voltages for the electrical part.
MAX4532EAP Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX4532EAP Applications
There are a lot of Maxim Integrated MAX4532EAP Analog Switches & Multiplexers ICs applications.
- Residential Gateways, Home Gateway/Router
- PBXs
- SDH/SONET multiplexers
- T1/E1 Terminals
- Communication systems
- Data Acquisition Systems
- Digital Cross-Connects
- MP3 players
- Audio and video switching
- Transmit
