MAX4533CPP
| Parameters | |
|---|---|
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 6Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 250ns, 150ns |
| Charge Injection | 1.5pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -66dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Switch-off Time-Max | 150ns |
| Length | 26.16mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2001 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 800mW |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4533 |
| Output | SEPARATE OUTPUT |
| Pin Count | 20 |
| Operating Supply Voltage | 18V |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 1mA |
| Max Supply Current | 600μA |
| Turn On Delay Time | 300 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 20nA |
MAX4533CPP Overview
The electronic component is convenient to ship overseas because it is packed in a 20-DIP (0.300, 7.62mm). This high-reliability packaging method uses advanced packaging methods Tube. The multiplexer is located in Through Hole. Multiplexers and demultiplexers have the same number of circuits 2:1. Operating temperature extended to 0°C~70°C TA. The total number of terminations is 20. The electronic part provides high-quality output because it has 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. An electrical component like this is included in the 20 series. Circuits based on SPDT switching are used to construct these analog switch ics. The multiplexer consists of 4 circuits. Using the MAX4533 search parameter, you can discover variants of the switch. It has an internal resistance of 175Ohm. For functions related to 20 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. Analog switch ics with Dual, Single supply type are cost-effective. It is recommended to use 9V as the lowest voltage for the electrical part. It may damage the digital multiplexer if the voltage is higher than 600μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 18V. For dual power supplies, a voltage of at least 4.5V should be attached. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. There is a voltage range of 18V operating voltages for the electrical part.
MAX4533CPP Features
1 Channels
Switch Circuit: SPDT
MAX4533CPP Applications
There are a lot of Maxim Integrated MAX4533CPP Analog Switches & Multiplexers ICs applications.
- Automatic test equipment
- Relay Replacement
- Medical Instrumentation
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- RGB switches
- Sample hold systems
- Automotive applications
- Private Branch Exchange (PBX)
- Microwave transmission systems
- Relay replacements
