MAX4533EAP
| Parameters | |
|---|---|
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 20nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 6Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 250ns, 150ns |
| Charge Injection | 1.5pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -66dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Switch-off Time-Max | 150ns |
| Height | 1.78mm |
| Length | 7.33mm |
| Width | 5.38mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2001 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4533 |
| Pin Count | 20 |
| Operating Supply Voltage | 18V |
| Polarity | Non-Inverting |
| Power Supplies | 12/+-15V |
| Number of Channels | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 1mA |
| Max Supply Current | 600μA |
| Turn On Delay Time | 300 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
MAX4533EAP Overview
Shipping overseas is convenient due to the electrical component's packing in 20-SSOP (0.209, 5.30mm Width). Advanced packaging method Tube is used to provide high reliability. It is mounted in the position Surface Mount. 2:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature extended to -40°C~85°C TA. 20 terminations have been made so far. A high-quality output is provided by the electrical component's 4 channels. A 15V voltage supply should turn on and run the electronic component. An electrical component of this type can be found in the 20 series. Unlike digital switches, these are based on SPDT switching circuits. Look for analog switch ic variants by searching with MAX4533. It has an internal resistance of 175Ohm. To find out what the functions of 20 pins are, please refer to their datasheets. It is a typical Multiplexer or Switches analog multiplexer. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. A analog switch ic that has a cost-effective Dual, Single supply type. It is recommended to use 9V as the lowest voltage for the electrical part. Putting voltage greater than 600μA on the multiplexer may cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 18V. It is recommended that you attach at least 4.5V to your dual power supply. This electrical part is compatible with 18V operating voltages.
MAX4533EAP Features
4 Channels
Switch Circuit: SPDT
MAX4533EAP Applications
There are a lot of Maxim Integrated MAX4533EAP Analog Switches & Multiplexers ICs applications.
- Precision instrumentation
- Communication systems
- Mechanical reed relay replacement
- Switching Systems
- Imaging
- Fiber to the Home
- RGB switches
- Precision test equipment
- Industrial and process control systems
- Cell phones
