MAX4533EAP-T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2001 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 800mW |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Output | SEPARATE OUTPUT |
| Pin Count | 20 |
| Operating Supply Voltage | 18V |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 1mA |
| Max Supply Current | 600μA |
| Turn On Delay Time | 300 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 20nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 6Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 250ns, 150ns |
| Charge Injection | 1.5pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -66dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Switch-off Time-Max | 150ns |
| Height Seated (Max) | 1.99mm |
| Length | 7.2mm |
| Width | 5.29mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4533EAP-T Overview
This electronic part is conveniently packaged in 20-SSOP (0.209, 5.30mm Width), making it easy to ship abroad. The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a ratio of 2:1. Operational temperature extended around -40°C~85°C TA. A total of 20 terminations have been recorded. A high-quality output is provided by the electrical component's 1 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. A total of 20 pins are injected into the body of the electronic part. Multiplexers built on a SPDT switching circuit are built. 4 circuits are used in this analogue multiplexer. Internally, this switch multiplexer has a resistance of 175Ohm. Please refer to the datasheets for 20 pins functions. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 36V volts for the multiplexer. A analog switch ic that has a cost-effective Dual, Single supply type. There should be 9V voltage fed to the electrical part below 9V. The analogue multiplexer may be damaged if voltage is greater than 600μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 18V. A dual power supply should have at least 4.5V voltage attached. There are SEPARATE OUTPUT outputs on this analog switch ic. Operating voltages of 18V are compatible with the electrical part.
MAX4533EAP-T Features
1 Channels
Switch Circuit: SPDT
MAX4533EAP-T Applications
There are a lot of Maxim Integrated MAX4533EAP-T Analog Switches & Multiplexers ICs applications.
- High-Voltage
- Automatic test equipment
- SONET
- Multiplexers
- PBX interfaces
- Channel Banks
- Medical systems
- Communications systems
- Microprocessor controlled systems
- Industrial
