MAX4533EPP+
| Parameters | |
|---|---|
| Current - Leakage (IS(off)) (Max) | 20nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 6Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 250ns, 150ns |
| Charge Injection | 1.5pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -66dB @ 1MHz |
| Switch-on Time-Max | 250ns |
| Switch-off Time-Max | 150ns |
| Length | 26.16mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2001 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 889mW |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | MAX4533 |
| Pin Count | 20 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 1mA |
| Max Supply Current | 600μA |
| Turn On Delay Time | 300 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 175Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
MAX4533EPP+ Overview
The electrical component comes in 20-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tube. This analog switch is mounted in Through Hole. 2:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -40°C~85°C TA. The total number of terminations is 20. Due to its 1 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. A total of 20 pins are injected into the body of the electronic part. A SPDT switching circuit is used for these analog switches. There are 4 circuits in this multiplexer. Try searching for MAX4533 variants of the analog switch ic. The internal resistance of this digital multiplexer is 175Ohm. To find out what the 20 pins do, please refer to the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. It is recommended to use 9V as the lowest voltage for the electrical part. The switch multiplexer may be damaged if it is exposed to voltage greater than 600μA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 18V. When using dual power supplies, you should attach at least 4.5V. 18V operating voltages are supported by the electronic component.
MAX4533EPP+ Features
1 Channels
Switch Circuit: SPDT
MAX4533EPP+ Applications
There are a lot of Maxim Integrated MAX4533EPP+ Analog Switches & Multiplexers ICs applications.
- Frame Relay Equipment
- Audio and video switching
- RGB switches
- Residential Gateways, Home Gateway/Router
- Cross Connects
- Automatic test equipment
- Relay replacements
- Cable PC
- Fault Tolerant Systems
- Digital Cross-Connects
