Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
14-SOIC (0.154, 3.90mm Width) |
Number of Pins |
14 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2005 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
Resistance |
400Ohm |
Max Power Dissipation |
640mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
1 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
MAX4534 |
Pin Count |
14 |
Number of Channels |
4 |
Number of Circuits |
1 |
Max Supply Voltage |
36V |
Min Supply Voltage |
9V |
Operating Supply Current |
75μA |
Throw Configuration |
4PST |
Turn On Delay Time |
700 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
9V~36V ±4.5V~20V |
Supply Type |
Dual, Single |
Supply Current-Max (Isup) |
0.375mA |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
350 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
400Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
4:1 |
Off-state Isolation-Nom |
62 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
5pF 6.5pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SP4T |
Switch Time (Ton, Toff) (Max) |
275ns, 200ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
2 Ω |
Crosstalk |
-53dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
275ns |
Switch-off Time-Max |
200ns |
Signal Current-Max |
0.03A |
Length |
8.65mm |
Width |
3.9mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
MAX4534ESD Overview
This electronic part is conveniently packaged in 14-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. High reliability is achieved by using advanced packaging method Tube. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 4:1. The operating temperature is extended to around -40°C~85°C TA. 14 terminations have been made so far. By its 4 channels, the electronic component provides high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. A total of 14 pins are injected into the electrical part body. A SP4T switching circuit is used to build these analog multiplexers. The multiplexer consists of 1 circuits. Try searching for the analog switch ic with MAX4534 if you are looking for variants. This digital multiplexer has 400Ohm internal resistance. The functions of 14 pins can be found in the datasheets. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. A analog switch ic that has a cost-effective Dual, Single supply type. In order for the electronic part to function properly, the lowest voltage should be 9V. This multiplexer would work with 75μA current. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. The voltage should be at least 4.5V if you are using dual power supplies.
MAX4534ESD Features
4 Channels
Switch Circuit: SP4T
75μA Supply Current
MAX4534ESD Applications
There are a lot of Maxim Integrated MAX4534ESD Analog Switches & Multiplexers ICs applications.
- Transmit
- Imaging
- Power routing
- ATM
- Signal routing between systems
- Multi-Line E1 Interface Cards
- Industrial
- CSU
- Communication systems
- New designs requiring multiplexer functions