MAX4534EUD
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 400Ohm |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4534 |
| Pin Count | 14 |
| Operating Supply Voltage | 28V |
| Number of Channels | 4 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Operating Supply Current | 400μA |
| Propagation Delay | 350 ns |
| Turn On Delay Time | 500 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 0.375mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 400Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 6.5pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 275ns, 200ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -53dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 275ns |
| Switch-off Time-Max | 200ns |
| Signal Current-Max | 0.03A |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4534EUD Overview
The electronic part can be shipped overseas conveniently because it is packaged in 14-TSSOP (0.173, 4.40mm Width). High reliability is provided by advanced packaging method Tube. Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a number of circuits 4:1. Temperatures around -40°C~85°C TA are extended for operation. There are 14 terminations totally. The electronic part provides high-quality output because it has 4 channels. An 15V voltage supply should allow the electrical part to be turned on and run. 14 pins are injected to the electronic part body. On the other hand, analog switches can be constructed using SP4T switching circuits. It consists of 1 circuits. Look for analog switch ic variants by searching with MAX4534. Analog switches have 400Ohm internal resistance. Datasheets for functions of 14 pins are available. Users shouldn't supply more than 36V voltage to the switch device. A cost-effective Dual, Single supply type analogue multiplexer. The lowest voltage fed to the electronic component should be 9V. This multiplexer would work with 400μA current. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. A dual power supply should have at least 4.5V voltage attached. A voltage of 28V can be used to operate the electronic component.
MAX4534EUD Features
4 Channels
Switch Circuit: SP4T
400μA Supply Current
MAX4534EUD Applications
There are a lot of Maxim Integrated MAX4534EUD Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Communications systems
- Battery-powered systems
- Automatic test equipment
- PDH Multiplexers
- PBX interfaces
- Residential Gateways, Home Gateway/Router
- Signal routing between systems
- Communication systems
