MAX4534EUD+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 400Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX4534 |
| Pin Count | 14 |
| Operating Supply Voltage | 28V |
| Number of Channels | 4 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Operating Supply Current | 400μA |
| Propagation Delay | 350 ns |
| Turn On Delay Time | 500 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 0.375mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 400Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 6.5pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 275ns, 200ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -53dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 275ns |
| Switch-off Time-Max | 200ns |
| Signal Current-Max | 0.03A |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4534EUD+T Overview
As the electronic part is packed in 14-TSSOP (0.173, 4.40mm Width), international shipping is convenient. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 4:1. The operating temperature is extended to around -40°C~85°C TA. In total, there have been 14 terminations. A electrical component with 4 channels is capable of high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. 14 pins are injected to the electronic part body. Circuits based on SP4T switching are used to construct these analog switch ics. There are 1 circuits in this switch device. If you are looking for variants of the digital switch, trying search with MAX4534. Analog switches have 400Ohm internal resistance. The datasheets for the 14 pins explain the functions. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. Digital switch that provides Dual, Single power at a cost-effective price. It is recommended that the electrical component receives a voltage of 9V. An operating current of 400μA would be sufficient for this switch device. For this switch, a dual supply voltage is feasible, but it must not exceed 20VA dual power supply should have at least 4.5V voltage attached. 28V operating voltages can be used with this electrical part.
MAX4534EUD+T Features
4 Channels
Switch Circuit: SP4T
400μA Supply Current
MAX4534EUD+T Applications
There are a lot of Maxim Integrated MAX4534EUD+T Analog Switches & Multiplexers ICs applications.
- Relay replacements
- Microwave transmission systems
- SDH
- Avionics
- Communication systems
- Residential Gateways, Home Gateway/Router
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- New designs requiring multiplexer functions
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- USB 1.1 signal switching circuits
