MAX4535CSD
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 400Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4535 |
| Pin Count | 14 |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Current-Max (Isup) | 0.375mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 400Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 4pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 275ns, 200ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -53dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4535CSD Overview
Due to its 14-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tube. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. Operating temperature around 0°C~70°C TA extended. In total, 14 terminations have occurred. A high-quality output is provided by the electrical component's 2 channels. A 15V voltage supply should turn on and run the electronic component. The electrical component body receives 14 pins. These analog multiplexers are built based on DPST - NO switching circuits. Circuits number 2 make up this analogue multiplexer. Look for analog switch ic variants by searching with MAX4535. Analog switches have 400Ohm internal resistance. Datasheets for 14 pin functions are available upon request. It is a typical Multiplexer or Switches analog multiplexer. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. It is recommended that the electrical component receives a voltage of 9V. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. A dual power supply should have at least 4.5V voltage attached. With a SINGLE-ENDED MULTIPLEXER analog IC integrated into the board.
MAX4535CSD Features
2 Channels
Switch Circuit: DPST - NO
MAX4535CSD Applications
There are a lot of Maxim Integrated MAX4535CSD Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- RGB switches
- Fiber In The Loop (FITL)
- SONET/SDH ADM
- Digital cross connects (DSX-1)
- Audio signal routing
- Wireless Local Loop
- Precision data acquisition
- Central office
- Ultrasound
