MAX4535CUD+
| Parameters | |
|---|---|
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 400Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 500mW |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4535 |
| Pin Count | 14 |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Operating Supply Current | 75μA |
| Throw Configuration | DPST |
| Propagation Delay | 350 ns |
| Turn On Delay Time | 500 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 400Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 4pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 275ns, 200ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -53dB @ 1MHz |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
MAX4535CUD+ Overview
The electronic component is convenient to ship overseas because it is packed in a 14-TSSOP (0.173, 4.40mm Width). This high-reliability packaging method uses advanced packaging methods Tube. There is an analog multiplexer mounted in position Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. Operational temperature extended around 0°C~70°C TA. Total terminations are 14. The electronic part delivers high-quality output through its 2 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. As part of the design of the 14 series, this electronic part has been incorporated into the system. The analog switch ics are built using DPST - NO switching circuits. There are 2 circuits in this multiplexer. Try searching for MAX4535 variants of the analog switch ic. The internal resistance of this digital multiplexer is 400Ohm. The datasheets for the 14 pins explain the functions. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. Analogue multiplexer with a Dual, Single supply type that is cost-effective. It is recommended to use 9V as the lowest voltage for the electrical part. This digital switch can be operated with a current of 75μA. Despite this switch device's dual supply capability, its voltage should not exceed 20V. In the case of dual power supplies, you should connect at least 4.5V.
MAX4535CUD+ Features
2 Channels
Switch Circuit: DPST - NO
75μA Supply Current
MAX4535CUD+ Applications
There are a lot of Maxim Integrated MAX4535CUD+ Analog Switches & Multiplexers ICs applications.
- Fiber to the Home
- Microwave transmission systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Mechanical reed relay replacement
- Intelligent PBX
- ATM
- Remote wireless modules
- Microprocessor controlled systems
- Automotive applications
- Industrial and process control systems
