MAX4535EPD
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 400Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4535 |
| Pin Count | 14 |
| Operating Supply Voltage | 28V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 400μA |
| Propagation Delay | 350 ns |
| Turn On Delay Time | 500 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Current-Max (Isup) | 0.375mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 400Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 4pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 275ns, 200ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -53dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Length | 19.05mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4535EPD Overview
Shipping overseas is convenient with the electronic component packed in 14-DIP (0.300, 7.62mm). Advanced packaging method Tube is used to provide high reliability. This analog switch is mounted in Through Hole. Multiplexer and demultiplexer circuits have a number 2:1. Temperatures around -40°C~85°C TA are extended for operation. Totally, there are 14 terminations. High-quality output is provided by the electronic component's 2 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. As part of the design of the 14 series, this electronic part has been incorporated into the system. On the other hand, analog switches can be constructed using DPST - NO switching circuits. The circuits in this analogue multiplexer number 2. Try searching for the analog switch ic with MAX4535 if you are looking for variants. This digital multiplexer has 400Ohm internal resistance. The functions of 14 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 36V volts for the multiplexer. The lowest voltage fed to the electronic component should be 9V. 400μA current would be enough for this multiplexer to operate. There is no problem with using dual supply voltage, but it should not exceed 20V. In the case of dual power supplies, you should connect at least 4.5V. It is integrated with a SINGLE-ENDED MULTIPLEXER analog IC. This electrical part is compatible with 28V operating voltages.
MAX4535EPD Features
2 Channels
Switch Circuit: DPST - NO
400μA Supply Current
MAX4535EPD Applications
There are a lot of Maxim Integrated MAX4535EPD Analog Switches & Multiplexers ICs applications.
- Central office
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- PCMCIA cards
- Imaging
- Battery Powered Systems
- Audio/video switches
- Battery Powered Instruments
- Channelized and Unchannelized DS3 applications
- Wireless Local Loop
- USB 1.1 signal switching circuits
