MAX4535EUD
| Parameters | |
|---|---|
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 400Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4535 |
| Pin Count | 14 |
| Operating Supply Voltage | 28V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Operating Supply Current | 400μA |
| Propagation Delay | 350 ns |
| Turn On Delay Time | 500 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 0.375mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 400Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 4pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 275ns, 200ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -53dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
MAX4535EUD Overview
The electronic component is convenient to ship overseas because it is packed in a 14-TSSOP (0.173, 4.40mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. In Surface Mount, this analog switch is mounted. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 14. High-quality output is provided by the electronic component's 2 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. Electronic part bodies are injected with 14 pins. A DPST - NO switching circuit is used for these analog switches. It consists of 2 circuits. Try searching for MAX4535 variants of the analog switch ic. It has an internal resistance of 400Ohm. To find out what the 14 pins do, please refer to the datasheets. A voltage higher than 36V should not normally be supplied to the switches. The digital multiplexer has a low cost Dual, Single supply. 9V is the lowest voltage that should be fed to the electronic electronic part. The analogue multiplexer could operate on 400μA current. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. With dual power supplies, you should attach at least 4.5V. A voltage of 28V can be used to operate the electronic component.
MAX4535EUD Features
2 Channels
Switch Circuit: DPST - NO
400μA Supply Current
MAX4535EUD Applications
There are a lot of Maxim Integrated MAX4535EUD Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- Access Concentrators
- Voice over IP/DSL – Integrated Access Devices, Smart
- PCMCIA cards
- Cellular phones
- Battery Powered Systems
- Optical Applications
- Imaging
- Data switching
- Public switching systems
