MAX4536CSE
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4536 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Power Supplies | 3/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 50nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 100 ns |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 50 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 2pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 100ns, 50ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -75dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4536CSE Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tube. The multiplexer is located in Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Around 0°C~70°C TA is the extended operating temperature. In total, there are 16 terminations. High-quality output is provided by the electronic component's 1 channels. When a voltage supply of 5V is used, the electronic component should be turned on and run. This electrical component is included in the 16 series of products. Circuits based on SPST - NO switching are used to construct these analog switch ics. It consists of 4 circuits. Try searching with MAX4536 to find analog multiplexer variants. An switch multiplexer with 100Ohm internal resistance has a value of 100Ohm. A analogue multiplexer of this type is a Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 6V to the switch device in normal circumstances. Analog switch ics with Dual, Single supply type are cost-effective. A low voltage of 2V should be applied to the electronic component. For this digital switch to work, 1μA current would suffice. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 6V. When using dual power supplies, you should attach at least 2V. This analog switch ic utilizes SEPARATE OUTPUT output.
MAX4536CSE Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX4536CSE Applications
There are a lot of Maxim Integrated MAX4536CSE Analog Switches & Multiplexers ICs applications.
- Industrial control systems
- PBXs
- Data switching
- Intelligent PBX
- DSLAMs
- Video signal routing
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Signal routing between systems
- Fault Tolerant Systems
- Public switching systems
