MAX4536CSE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4536 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| On-State Resistance (Max) | 100Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 2pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 100ns, 50ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -75dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 100ns |
| Switch-off Time-Max | 50ns |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
MAX4536CSE+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have the same number of circuits 1:1. Operational temperature extended around 0°C~70°C TA. 16 terminations have been made so far. As a result of its 1 channels, this electronic component provides high-quality output. Powered by a 5V voltage supply, the electrical part should be switched on and run. An injection of 16 pins is performed into the body of the electrical component. On the other hand, analog switches can be constructed using SPST - NO switching circuits. The multiplexer consists of 4 circuits. Try searching with MAX4536 if you're looking for variants. In this analog multiplexer, the value is Multiplexer or Switches. The outputs of this digital multiplexer are SEPARATE OUTPUT in number.
MAX4536CSE+T Features
1 Channels
Switch Circuit: SPST - NO
MAX4536CSE+T Applications
There are a lot of Maxim Integrated MAX4536CSE+T Analog Switches & Multiplexers ICs applications.
- Audio and video signal routing
- Wireless Local Loop
- CSU
- Voice over IP/DSL – Integrated Access Devices, Smart
- Digital access cross connects
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Audio and video routing
- ATM
- Optical Applications
- Cell phones
