MAX4537CPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4537 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 3/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 2pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 100ns, 50ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -75dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 100ns |
| Switch-off Time-Max | 50ns |
| Normal Position | NC |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4537CPE Overview
The electronic component is convenient to ship overseas because it is packed in a 16-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. This analog switch is mounted in Through Hole. 1:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around 0°C~70°C TA. In total, there have been 16 terminations. The electronic part provides high-quality output because it has 1 channels. An 5V voltage supply should allow the electrical part to be turned on and run. There are 16 pins injected into the electronic part body. Based on SPST - NC switching circuits, these analog multiplexers work. This multiplexer is composed of 4 circuits. Look for analog switch ic variants by searching with MAX4537. It has an internal resistance of 100Ohm. For functions related to 16 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 12V. It is recommended that the electrical component receives a voltage of 2V. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 6V. In the case of dual power supplies, you should connect at least 2V. This analog switch ic utilizes SEPARATE OUTPUT output.
MAX4537CPE Features
1 Channels
Switch Circuit: SPST - NC
MAX4537CPE Applications
There are a lot of Maxim Integrated MAX4537CPE Analog Switches & Multiplexers ICs applications.
- Communication systems
- Relay replacements
- Fiber In The Loop (FITL)
- Battery-powered systems
- Imaging
- Fault Tolerant Systems
- Medical
- SDH/SONET multiplexers
- Digital cross connects (DSX-1)
- Microprocessor Controlled Analog Systems
