MAX4537CSE
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4537 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 3/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 2pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 100ns, 50ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -75dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 100ns |
| Switch-off Time-Max | 50ns |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4537CSE Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. Advanced packaging method Tube is used to provide high reliability. In Surface Mount, you'll find this switch device. 1:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around 0°C~70°C TA. Totally, there are 16 terminations. The electronic part provides high-quality output because it has 1 channels. A 5V voltage supply should turn on and run the electronic component. As part of its design, the 16 series is equipped with this electronic component. Multiplexers built on a SPST - NC switching circuit are built. The circuits in this analogue multiplexer number 4. Try searching with MAX4537 if you're looking for variants. It has an internal resistance of 100Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. It is recommended to use 2V as the lowest voltage for the electrical part. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 6V. If you are using dual power supplies, you should attach at least 2V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
MAX4537CSE Features
1 Channels
Switch Circuit: SPST - NC
MAX4537CSE Applications
There are a lot of Maxim Integrated MAX4537CSE Analog Switches & Multiplexers ICs applications.
- Data switching
- Relay replacements
- Audio and video routing
- Cell phones
- SDH/SONET multiplexers
- High speed data transmission line cards
- PBXs
- Multiplexers
- Sample-and-hold systems
- Isolation
