MAX4537ESE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Bulk |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Throw Configuration | SPST |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 2pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 100ns, 50ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -75dB @ 1MHz |
| Switch-on Time-Max | 100ns |
| Switch-off Time-Max | 50ns |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4537ESE+ Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers and demultiplexers have a ratio of 1:1. Increasing operating temperature to around -40°C~85°C TA. A total of 16 terminations have been recorded. This electronic part offers high-quality output due to its 1 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. 16 pins are injected to the electronic part body. Unlike digital switches, these are based on SPST - NC switching circuits. A 4 circuit is present in this switch device. There is 100Ohm internal resistance in this digital multiplexer. The datasheets for the 16 pins explain the functions. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. There should be 2V voltage fed to the electrical part below 2V. In order to operate this switch device, it would need a current of 1μA. There is no problem with using dual supply voltage, but it should not exceed 6V. It is recommended that you attach at least 2V to your dual power supply.
MAX4537ESE+ Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
MAX4537ESE+ Applications
There are a lot of Maxim Integrated MAX4537ESE+ Analog Switches & Multiplexers ICs applications.
- Wireless Local Loop
- Precision instrumentation
- Video switching
- Remote Powered Equipment
- Residential Gateways, Home Gateway/Router
- Sample-and-hold systems
- ISDN NT1/TA
- Low-Voltage
- Audio and video signal routing
- MP3 players
