Parameters |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
1996 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
200Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
4 |
Supply Voltage |
5V |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
MAX4538 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
JESD-30 Code |
R-PDIP-T16 |
Power Supplies |
3/+-5V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2V |
Operating Supply Current |
50nA |
Throw Configuration |
SPST |
Voltage - Supply, Single/Dual (±) |
2V~12V ±2V~6V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Max Dual Supply Voltage |
6V |
On-State Resistance (Max) |
100Ohm |
Min Dual Supply Voltage |
2V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
65 dB |
Current - Leakage (IS(off)) (Max) |
2nA |
Channel Capacitance (CS(off), CD(off)) |
2pF 2pF |
On-state Resistance Match-Nom |
4Ohm |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
100ns, 50ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
1 Ω |
Crosstalk |
-75dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
100ns |
Switch-off Time-Max |
50ns |
Length |
19.175mm |
Width |
7.62mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
MAX4538CPE Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). The advanced packaging method Tube provides high reliability. Mounted in Through Hole is this multiplexer. There is 1:1 ratio between the number of multiplexers and demultiplexers. Extended operating temperature around 0°C~70°C TA. The total number of terminations is 16. The electronic part provides high-quality output because it has 1 channels. With a 5V voltage supply, the electrical component should be turned on and run. A total of 16 pins are injected into the electrical part body. A SPST - NO/NC switching circuit is used to build these analog multiplexers. A total of 4 circuits make up this switch device. Try searching with MAX4538 if you're looking for variants. In this multiplexer, the internal resistance is 200Ohm. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 12V. The analog switch ic is of the Dual, Single supply type and is cost-effective. It is recommended that the electrical component receives a voltage of 2V. The switch device would be able to operate with 50nA current. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 6V. You should attach at least 2V voltage if you are using dual power supply. SEPARATE OUTPUT outputs are utilized by this digital multiplexer.
MAX4538CPE Features
1 Channels
Switch Circuit: SPST - NO/NC
50nA Supply Current
MAX4538CPE Applications
There are a lot of Maxim Integrated MAX4538CPE Analog Switches & Multiplexers ICs applications.
- Battery Powered Systems
- Communication systems
- Sample-and-hold systems
- Residential Gateways, Home Gateway/Router
- Battery Powered Instruments
- DSUs
- Fiber to the Home
- Cable PC
- Precision instrumentation
- Audio/video switches