Parameters |
Switch Time (Ton, Toff) (Max) |
100ns, 50ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
1 Ω |
Crosstalk |
-75dB @ 1MHz |
Switch-on Time-Max |
100ns |
Switch-off Time-Max |
50ns |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Published |
1996 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
100Ohm |
Terminal Finish |
TIN |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
5V |
Terminal Pitch |
1.27mm |
Pin Count |
16 |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2V |
Voltage - Supply, Single/Dual (±) |
2V~12V ±2V~6V |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Max Dual Supply Voltage |
6V |
On-State Resistance (Max) |
100Ohm |
Min Dual Supply Voltage |
2V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
65 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
2pF 2pF |
On-state Resistance Match-Nom |
4Ohm |
Switch Circuit |
SPST - NO/NC |
MAX4538CSE+ Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. A switch device like this is mounted in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operating temperature extended to 0°C~70°C TA. The total number of terminations is 16. A high-quality output is provided by the electrical component's 1 channels. An 5V voltage supply should allow the electrical part to be turned on and run. The electrical component body receives 16 pins. These analog multiplexers are built based on SPST - NO/NC switching circuits. A 4 circuit is present in this switch device. A 100Ohm internal resistance characterizes this multiplexer. To find out what the 16 pins do, please refer to the datasheets. In normalcircumstances, users should not exceed 12V volts for the multiplexer. A low voltage of 2V should be applied to the electronic component. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 6V. If you are using a dual power supply, you should attach at least 2V.
MAX4538CSE+ Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4538CSE+ Applications
There are a lot of Maxim Integrated MAX4538CSE+ Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- Cable PC
- Remote wireless modules
- PBXs
- Access Concentrators
- High speed data transmission line cards
- Power routing
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Signal routing between systems
- Mechanical reed relay replacement