MAX4541CUA+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4541 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 100pA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 125 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 400 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 76 dB |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 100ns |
| Switch-off Time-Max | 75ns |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Normal Position | NO |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
MAX4541CUA+T Overview
Packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 1:1. Operation at a temperature around 0°C~70°C TA. A total of 8 terminations have been recorded. A electrical component with 1 channels is capable of high-quality output. With a 5V voltage supply, the electrical component should be turned on and run. It is injected into the electrical part body with 8 pins. Unlike digital switches, these are based on SPST - NO switching circuits. There are 2 circuits in this switch device. MAX4541 can be used to search for analog multiplexer variants. There is 60Ohm internal resistance in this digital multiplexer. For details about the functions of 8 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users should never supply a voltage higher than 12V to a switch device. Single supply type digital switch with a low cost. It is recommended to use 2.7V as the lowest voltage for the electrical part. The analogue multiplexer could operate on 100pA current. Using a single voltage supply, this switch device consumes 2.7V~12V volts. When the digital multiplexer is charged above 1μA, damage can occur. There are SEPARATE OUTPUT outputs on this analog switch ic. 9V operating voltages can be used with this electrical part.
MAX4541CUA+T Features
1 Channels
Switch Circuit: SPST - NO
100pA Supply Current
MAX4541CUA+T Applications
There are a lot of Maxim Integrated MAX4541CUA+T Analog Switches & Multiplexers ICs applications.
- Relay replacements
- Automatic test equipment
- Microprocessor Controlled Analog Systems
- SDH
- Avionics and Military Systems
- Digital cross connects (DSX-1)
- Remote Powered Equipment
- Remote wireless modules
- Video switching
- RGB switches
