MAX4541EPA
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4541 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| JESD-30 Code | R-PDIP-T8 |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 100pA |
| Throw Configuration | SPST |
| Supply Type | Single |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 76 dB |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 100ns |
| Switch-off Time-Max | 75ns |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Normal Position | NO |
| Length | 9.375mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4541EPA Overview
The electronic component is convenient to ship overseas because it is packed in a 8-DIP (0.300, 7.62mm). This high-reliability packaging method uses advanced packaging methods Tube. This analog switch is mounted in Through Hole. Multiplexer and demultiplexer circuits have a number 1:1. Operational temperature extended around -40°C~85°C TA. Totally, there are 8 terminations. A electrical component with 1 channels is capable of high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. A total of 8 pins are injected into the electrical part body. Based on SPST - NO switching circuits, these analog multiplexers work. There are 2 circuits in this multiplexer. Look for analog switch ic variants by searching with MAX4541. Internally, this switch multiplexer has a resistance of 60Ohm. Theswitch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 12V. The analog switch ic is of the Single supply type and is cost-effective. It is recommended that the electrical component receives a voltage of 2.7V. 100pA current would be enough for this multiplexer to operate. A voltage of 2.7V~12V is required to drain this analog switch from a single voltage supply. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.
MAX4541EPA Features
1 Channels
Switch Circuit: SPST - NO
100pA Supply Current
MAX4541EPA Applications
There are a lot of Maxim Integrated MAX4541EPA Analog Switches & Multiplexers ICs applications.
- Sample hold systems
- Fiber to the Home
- E1 Network Equipment
- Channel Banks
- FTTH
- Data Acquisition Systems
- Avionics test equipment
- Cell phones
- Sample-and-hold systems
- Optical Applications
