MAX4541ESA-T
| Parameters | |
|---|---|
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 100pA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 125 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 400 ns |
| On-State Resistance (Max) | 60Ohm |
| High Level Output Current | 10mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 76 dB |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 100ns |
| Switch-off Time-Max | 75ns |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 60Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | MAX4541 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Operating Supply Voltage | 9V |
| Polarity | Non-Inverting |
MAX4541ESA-T Overview
Shipping overseas is convenient with the electronic component packed in 8-SOIC (0.154, 3.90mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a ratio of 1:1. Extended operating temperature around -40°C~85°C TA. In total, there have been 8 terminations. High-quality output is provided by the electronic component's 1 channels. An 5V voltage supply should allow the electrical part to be turned on and run. This electronic part can be found in the 8 series. A SPST - NO switching circuit is used for these analog switches. The multiplexer consists of 2 circuits. Try searching for MAX4541 variants of the analog switch ic. As far as internal resistance is concerned, it has 60Ohm. In this analog multiplexer, the value is Multiplexer or Switches. In normalcircumstances, users should not exceed 12V volts for the multiplexer. The analog switch ic is of the Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 2.7V. The analogue multiplexer could operate on 100pA current. Analogue multiplexers require a 2.7V~12V voltage to drain from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 1μA. 9V operating voltages are supported by the electronic component.
MAX4541ESA-T Features
1 Channels
Switch Circuit: SPST - NO
100pA Supply Current
MAX4541ESA-T Applications
There are a lot of Maxim Integrated MAX4541ESA-T Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- Audio signal routing
- Switching Systems
- Avionics and Military Systems
- Battery Powered Instruments
- Automatic test equipment
- Industrial control systems
- Audio and video switching
- Precision data acquisition
- Data Acquisition Systems
