Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
Number of Pins |
8 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2007 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Resistance |
60Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
471mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
2 |
Supply Voltage |
5V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
MAX4541 |
Output |
SEPARATE OUTPUT |
Pin Count |
8 |
Operating Supply Voltage |
9V |
Power Supplies |
3.3/5V |
Number of Channels |
2 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2.7V |
Operating Supply Current |
100pA |
Nominal Supply Current |
1μA |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
125 ns |
Supply Type |
Single |
Turn-Off Delay Time |
400 ns |
On-State Resistance (Max) |
60Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
76 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
8pF 8pF |
On-state Resistance Match-Nom |
0.8Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
100ns, 75ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
800m Ω |
Crosstalk |
-90dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
100ns |
Switch-off Time-Max |
75ns |
Voltage - Supply, Single (V+) |
2.7V~12V |
Normal Position |
NO |
Height Seated (Max) |
1.1mm |
Length |
3mm |
Width |
3mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
MAX4541EUA Overview
Due to its 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) packaging, the electronic part is convenient for international shipping. To ensure high reliability, a new packaging method Tube is used. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Around -40°C~85°C TA is the extended operating temperature. There are 8 terminations totally. As a result of its 2 channels, this electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 5V voltage supply. A key feature of the 8 series is the inclusion of this electronic part as part of its design. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Look for analog switch ic variants by searching with MAX4541. There is 60Ohm internal resistance in this digital multiplexer. The functions of 8 pins can be found in the datasheets. This switch device is a typical Multiplexer or Switches. Users shouldn't supply more than 12V voltage to the switch device. Analog switch ics with Single supply type are cost-effective. The lowest voltage the electronic part should receive is 2.7V. An operating current of 100pA would be sufficient for this switch device. A voltage of 2.7V~12V is required to drain this analog switch from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. The electronic component can function from 9V.
MAX4541EUA Features
2 Channels
Switch Circuit: SPST - NO
100pA Supply Current
MAX4541EUA Applications
There are a lot of Maxim Integrated MAX4541EUA Analog Switches & Multiplexers ICs applications.
- Cross Connects
- Audio and video switching
- Audio and video signal routing
- Mechanical reed relay replacement
- Residential Gateways, Home Gateway/Router
- Low-Voltage
- Battery Powered Systems
- Remote Powered Equipment
- PDH Multiplexers
- PBXs