MAX4541EUA+T
| Parameters | |
|---|---|
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4541 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 100pA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 125 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 400 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 76 dB |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 100ns |
| Switch-off Time-Max | 75ns |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Normal Position | NO |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
MAX4541EUA+T Overview
This electronic part is conveniently packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), making it easy to ship abroad. High reliability is achieved by using advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature around -40°C~85°C TA extended. There are 8 terminations totally. As a result of its 1 channels, this electronic component provides high-quality output. Powered by a 5V voltage supply, the electrical part should be switched on and run. A total of 8 pins are injected into the electrical part body. These analog multiplexers are built based on SPST - NO switching circuits. There are 2 circuits in this switch device. Search with MAX4541 if you are looking for analog multiplexer variants. As far as internal resistance is concerned, it has 60Ohm. The datasheets for the 8 pins explain the functions. This switch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 12V volts for the multiplexer. Digital switch that provides Single power at a cost-effective price. In order for the electronic part to function properly, the lowest voltage should be 2.7V. The switch device would be able to operate with 100pA current. An analogue multiplexer drains from a single voltage supply at 2.7V~12V. The analogue multiplexer may be damaged if voltage is greater than 1μA. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. There is a voltage range of 9V operating voltages for the electrical part.
MAX4541EUA+T Features
1 Channels
Switch Circuit: SPST - NO
100pA Supply Current
MAX4541EUA+T Applications
There are a lot of Maxim Integrated MAX4541EUA+T Analog Switches & Multiplexers ICs applications.
- Sample hold systems
- PDAs
- Access Concentrators
- Industrial
- RGB switches
- New designs requiring multiplexer functions
- FTTH
- Isolation
- Relay Replacement
- Sample-and-hold systems
