banner_page

MAX4542EKA-T

100ns, 75ns SPST - NC 60Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4542 8 Pins 5V SOT-23-8


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX4542EKA-T
  • Package: SOT-23-8
  • Datasheet: PDF
  • Stock: 648
  • Description: 100ns, 75ns SPST - NC 60Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4542 8 Pins 5V SOT-23-8(Kg)

Details

Tags

Parameters
Mount Surface Mount
Mounting Type Surface Mount
Package / Case SOT-23-8
Number of Pins 8
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2007
JESD-609 Code e4
Pbfree Code no
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
Resistance 60Ohm
Terminal Finish Nickel/Palladium/Gold (Ni/Pd/Au)
Subcategory Multiplexer or Switches
Max Power Dissipation 330mW
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 240
Number of Functions 2
Supply Voltage 5V
Terminal Pitch 0.65mm
Time@Peak Reflow Temperature-Max (s) 20
Base Part Number MAX4542
Output SEPARATE OUTPUT
Pin Count 8
Power Supplies 3.3/5V
Number of Channels 1
Number of Circuits 2
Max Supply Voltage 12V
Min Supply Voltage 2.7V
Nominal Supply Current 100pA
Max Supply Current 1μA
Throw Configuration SPST
Turn On Delay Time 100 ns
Supply Type Single
Turn-Off Delay Time 75 ns
On-State Resistance (Max) 60Ohm
Multiplexer/Demultiplexer Circuit 1:1
Off-state Isolation-Nom 76 dB
Channel Capacitance (CS(off), CD(off)) 8pF 8pF
On-state Resistance Match-Nom 0.8Ohm
Switch Circuit SPST - NC
Switch Time (Ton, Toff) (Max) 100ns, 75ns
Charge Injection 1pC
Channel-to-Channel Matching (ΔRon) 800m Ω
Crosstalk -90dB @ 1MHz
Switching BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+) 2.7V~12V
Normal Position NC
Height Seated (Max) 1.45mm
Radiation Hardening No
RoHS Status Non-RoHS Compliant
Lead Free Contains Lead

MAX4542EKA-T Overview


Due to its SOT-23-8 packaging, the electronic part is convenient for international shipping. High reliability is provided by advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. In total, 8 terminations have occurred. The electronic part delivers high-quality output through its 1 channels. A 5V voltage supply should turn on and run the electronic component. As part of the design of the 8 series, this electronic part has been incorporated into the system. A SPST - NC switching circuit is used to build these analog multiplexers. 2 circuits are used in this analogue multiplexer. Use MAX4542 to search for variants of the digital switches. The internal resistance of this digital multiplexer is 60Ohm. The functions of 8 pins can be found in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. In normalcircumstances, users should not exceed 12V volts for the multiplexer. Analogue multiplexers of the Single supply type that are cost-effective. It is recommended to use 2.7V as the lowest voltage for the electrical part. Using only a single voltage supply, this analog switch requires 2.7V~12V voltage. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. This analog switch ic utilizes SEPARATE OUTPUT output.

MAX4542EKA-T Features


1 Channels
Switch Circuit: SPST - NC

MAX4542EKA-T Applications


There are a lot of Maxim Integrated MAX4542EKA-T Analog Switches & Multiplexers ICs applications.

  • RGB switches
  • Data Acquisition Systems
  • Voice over IP/DSL – Integrated Access Devices, Smart
  • SDH/SONET multiplexers
  • Mechanical reed relay replacement
  • Sample hold systems
  • Channelized and Unchannelized DS3 applications
  • Cable Telephony – NIU, Set-Top Box, Home Side Box
  • DVD-R
  • DSUs

Write a review

Note: HTML is not translated!
    Bad           Good