MAX4542EUA+
| Parameters | |
|---|---|
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 330mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4542 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 100pA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 75 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 76 dB |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Normal Position | NC |
| Height | 950μm |
| Length | 3.1mm |
| Width | 3.1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
MAX4542EUA+ Overview
Packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), the electronic component is convenient for shipping overseas. In order to provide high reliability, an advanced packaging method Tube is used. This analog switch is mounted in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. A total of 8 terminations have been recorded. The electronic part delivers high-quality output through its 1 channels. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. A key feature of the 8 series is the inclusion of this electronic part as part of its design. These analog multiplexers are built based on SPST - NC switching circuits. It consists of 2 circuits. Try searching for the analog switch ic with MAX4542 if you are looking for variants. There is 60Ohm internal resistance in this digital multiplexer. The functions of 8 pins can be found in the datasheets. Theswitch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. An effective Single supply digital multiplexer. It is recommended that the electrical component receives a voltage of 2.7V. Using only a single voltage supply, this analog switch requires 2.7V~12V voltage. It may damage the digital multiplexer if the voltage is higher than 1μA. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
MAX4542EUA+ Features
1 Channels
Switch Circuit: SPST - NC
MAX4542EUA+ Applications
There are a lot of Maxim Integrated MAX4542EUA+ Analog Switches & Multiplexers ICs applications.
- E1 Network Equipment
- Central office
- Microprocessor Controlled Analog Systems
- FTTH
- Channelized and Unchannelized DS3 applications
- Ultrasound
- Battery Powered Systems
- Precision instrumentation
- Automotive applications
- Routers
