MAX4543EPA
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 60Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4543 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| JESD-30 Code | R-PDIP-T8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Throw Configuration | SPST |
| Supply Type | Single |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 76 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 100ns |
| Switch-off Time-Max | 75ns |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Length | 9.375mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4543EPA Overview
Shipping overseas is convenient with the electronic component packed in 8-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. A switch device like this is mounted in Through Hole. Multiplexers and demultiplexers have a ratio of 1:1. Extended operating temperature around -40°C~85°C TA. In total, 8 terminations have occurred. By its 1 channels, the electronic component provides high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. An electrical component like this is included in the 8 series. A SPST - NO/NC switching circuit is used for these analog switches. There are 2 circuits in this multiplexer. MAX4543 can be used to search for analog multiplexer variants. In this multiplexer, the internal resistance is 60Ohm. The analog multiplexer shown here is a typical Multiplexer or Switches. The digital multiplexer has a low cost Single supply. A voltage of 2.7V~12V is required for this switch device, which drains from a single voltage source. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
MAX4543EPA Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4543EPA Applications
There are a lot of Maxim Integrated MAX4543EPA Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Channel Banks
- Microprocessor controlled systems
- CSU
- Medical systems
- High speed data transmission line cards
- E1 Multiplexer
- Audio and video routing
- Switching Systems
