MAX4544CPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 60Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX4544 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 2 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 100pA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 75 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 76 dB |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Length | 9.375mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX4544CPA+ Overview
Shipping overseas is convenient due to the electrical component's packing in 8-DIP (0.300, 7.62mm). Advanced packaging method Tube is used to provide high reliability. In Through Hole, you'll find this switch device. Multiplexers and demultiplexers have the same number of circuits 2:1. Temperatures around 0°C~70°C TA are extended for operation. 8 terminations have been made so far. A 2 channel electronic part produces high-quality output. With a 5V voltage supply, the electrical component should be turned on and run. 8 pins are injected to the electronic part body. The analog switch ics are built using SPDT switching circuits. The multiplexer consists of 1 circuits. Try searching with MAX4544 if you're looking for variants. An switch multiplexer with 60Ohm internal resistance has a value of 60Ohm. For functions related to 8 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 12V. Single supply type digital switch with a low cost. There should be 2.7V voltage fed to the electrical part below 2.7V. Using only a single voltage supply, this analog switch requires 2.7V~12V voltage. It may damage the digital multiplexer if the voltage is higher than 1μA. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.
MAX4544CPA+ Features
2 Channels
Switch Circuit: SPDT
MAX4544CPA+ Applications
There are a lot of Maxim Integrated MAX4544CPA+ Analog Switches & Multiplexers ICs applications.
- Fiber In The Loop (FITL)
- PDH Multiplexers
- Avionics
- Multi-Line E1 Interface Cards
- Relay Replacement
- Sample hold systems
- DSLAMs
- SDH
- Private Branch Exchange (PBX)
- Data switching
