MAX4544CPA
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4544 |
| Pin Count | 8 |
| JESD-30 Code | R-PDIP-T8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 76 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 75ns |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
MAX4544CPA Overview
Shipping overseas is convenient due to the electrical component's packing in 8-DIP (0.300, 7.62mm). This high-reliability packaging method uses advanced packaging methods Tube. The multiplexer is located in Through Hole. 2:1 is the ratio of multiplexer to demultiplexer circuits. Temperatures around 0°C~70°C TA are extended for operation. In total, there are 8 terminations. As a result of its 1 channels, this electronic component provides high-quality output. Powered by a 5V voltage supply, the electrical part should be switched on and run. Electronic part bodies are injected with 8 pins. SPDT switching circuits are used in these analog switch ics. The circuits in this analogue multiplexer number 1. Using the MAX4544 search parameter, you can discover variants of the switch. The analogue multiplexer in this example is a typical Multiplexer or Switches. This analog switch requires a voltage of 2.7V~12V to drain from a single voltage supply.
MAX4544CPA Features
1 Channels
Switch Circuit: SPDT
MAX4544CPA Applications
There are a lot of Maxim Integrated MAX4544CPA Analog Switches & Multiplexers ICs applications.
- Relay replacements
- PBX interfaces
- HDTV
- Fiber In The Loop (FITL)
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Remote Powered Equipment
- PCMCIA cards
- Video signal routing
- Wireless Local Loop
- Data switching
