MAX4544CSA+
| Parameters | |
|---|---|
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 76 dB |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Drain to Source Resistance | 60Ohm |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4544 |
| Pin Count | 8 |
| Power Supplies | 3.3/5V |
| Number of Channels | 2 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 100pA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 75 ns |
| On-State Resistance (Max) | 60Ohm |
MAX4544CSA+ Overview
The electronic component is convenient to ship overseas because it is packed in a 8-SOIC (0.154, 3.90mm Width). Advanced packaging method Tube is used to provide high reliability. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 2:1. Increasing operating temperature to around 0°C~70°C TA. In total, there are 8 terminations. By its 2 channels, the electronic component provides high-quality output. When a voltage supply of 5V is used, the electronic component should be turned on and run. As part of its design, the 8 series is equipped with this electronic component. The analog switch ics are built using SPDT switching circuits. There are 1 circuits in this switch device. MAX4544 can be used to search for analog multiplexer variants. In this multiplexer, the internal resistance is 60Ohm. The datasheets for the 8 pins explain the functions. There is a standard Multiplexer or Switches analogue multiplexer here. normally, users should not supply switches with voltages higher than 12V. The analog switch ic is of the Single supply type and is cost-effective. It is recommended that the electrical component receives a voltage of 2.7V. Analogue multiplexers require a 2.7V~12V voltage to drain from a single voltage supply. When the digital multiplexer is charged above 1μA, damage can occur. Drain to Source resistance for this electronic component is 60Ohm.
MAX4544CSA+ Features
2 Channels
Switch Circuit: SPDT
Drain-to-Source resistance: 60Ohm
MAX4544CSA+ Applications
There are a lot of Maxim Integrated MAX4544CSA+ Analog Switches & Multiplexers ICs applications.
- Cable PC
- Ultrasound
- MP3 players
- Fault Tolerant Systems
- Data switching
- Precision data acquisition
- Audio signal routing
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- DSLAMs
- Video signal routing
